Big Discount Digital Promotion Product Collections with Free Shipping Delivery from Market Goods Choice Great Customer Testimonial provide best electronic testimonials,high rating electronics Rf Remote Wireless 433 Satisfied Module 12v 1ch Jumper Electronic Control Universal Receiver Consumer Dc Transmitter.
Rf Remote Wireless 433 Satisfied Module 12v 1ch Jumper Electronic Control Universal Receiver Consumer Dc Transmitter Taryn Treasure Rating: 4.0 out of 5 Get Discount Now! Only US $1.70/piece at this time. Hurry buy Now before back to normal price! Normal price US $2.39 or you can Check price now. Dont waste your time. Buy Now only at KTNNKG Official Store Trusted Seller Store!
Receiver Description :1, the working voltage: DC12V2, quiescent current: 8mA3, operating frequency: 433MHz , other frequencies can be customized4, the load current: 10A5, power power: 2200W6, receiving sensitivity: -105dbm7, frequency deviation: ± 0.2MHz8, encoding method: learning type9, working mode: jog, self-locking, interlocking, delay10. Modulation method: ASK11, remote control distance: 100M (wild)12, PCBA size: 39mm*48mm*18mm13, shell size: 80MM *55MM *25MMTransmitter Description:DC12V, 433MHz ( ±0.2MHz ), 10-15mwWorking current: 9-12mA Launch distance: 50-100m Chip: PT2260 (fixed code), EV1527 SIZE :55mm / 30mm / 10mmWeight: 35gThe wiring instructions：1,+ : Connect to the positive 12V power supply;2. - : Connect to the negative electrode of 12V power supply;3, NO: output; normally open end of the relay;4, COM: output; relay public end;5, NC: output; normally closed relay;Function selection：1. Set to jog output: Remove the jumper cap on the board.2. Set as self-locking output: short the “T” and the middle pin with the jumper on the board.3, set to interlock output: use the jumper cap on the board to short "L" and the middle pin. Learning code.(Note "Learning code" means "matching"):1. Power the circuit board and the LED lights up.2. Press the KEY button on the PCBA board. After the LED goes out, release the button.3. Press any key on the remote control and the LED will blink.4, learning code OK.Clear the original code:1. Power the circuit board and the LED lights up.2. Press the KEY button on the PCBA board and do not release it.3. After seeing the LED flash, release the button.4, clear OK.The output mode explained:1. Self-locking: Press the remote controller "A" once to pull the relay. Press the remote controller "A" again and the relay turns off.2. Interlock: Press the "A" key of the remote control and the relay will pull in. Press the remote control "B" key, the relay is off.3. Jog: press the remote control "A" key, the relay pulls, release the remote control "A" key, the relay is disconnected. If you keep pressing it, the relay will keep on pulling until you release the "A" key of the remote controller.
Return Policy
If the product you receive is not as described or low quality, the seller promises that you may return it before order completion (when you click "Confirm Order Received" or exceed confirmation timeframe) and receive a full refund. The return shipping fee will be paid by you. Or, you can choose to keep the product and agree the refund amount directly with the seller.
N.B.: If the seller provides the "Longer Protection" service on this product, you may ask for refund up to 15 days after order completion.
Seller Service
On-time Delivery: If you do not receive your purchase within 60 days, you can ask for a full refund before order completion (when you click "Confirm Order Received" or exceed confirmation timeframe).
Rf Remote Wireless 433 Satisfied Module 12v 1ch Jumper Electronic Control Universal Receiver Consumer Dc Transmitter
No comments:
Post a Comment